MC Three-terminal Positive Voltage Regulator These voltage regulators are monolithic integrated circuits designed as fixedvoltage regulators for a wide. MC Fairchild datasheet pdf data sheet FREE Datasheets (data sheet) search for integrated circuits (ic), semiconductors and other electronic components. Motorola Semiconductor MC datasheet, (MC Series) Three Terminal Positive Fixed Voltage Regulators (1-page), MC datasheet, MC pdf.
|Published (Last):||6 January 2012|
|PDF File Size:||16.65 Mb|
|ePub File Size:||18.94 Mb|
|Price:||Free* [*Free Regsitration Required]|
Internal Thermal Overload Protection? That means that when your load consumes 10W the switcher will only dissipate 1W. There are LDOs Low Drop-Out which still can regulate the output if the input is only a few hundreds of mV higher and there are even ultra low drop-out types mmc7812 only need a few tens of mV.
Current Boost Regulator Figure Maximum Power Dissipation – The maximum total device dissipation for which the regulator will operate within specifications. Peter Mortensen 1, 3 14 If so, what is the current like that it outputs? If we look further we can see two values for line regulation; it appears that this is best if the input voltage is at least 16V. The minimum voltage obtainable with this arrangement is 2. Dean 4, 22 57 Internal Short Circuit Current Limiting?
If you have an input voltage of 20V the same 1A will be drawn from that 20V. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur.
So if you have a 12W load it will draw 1A from the regulator. All linear regulators have a minimum dropout voltageor difference.
The is not datasheeet LDO low-dropout regulatoras the typical dropout voltage is around 2 volts. In many low current applications, compensation capacitors are not required. Sign mc8712 using Facebook. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. From the above it may look like you best make your input voltage a lot higher than the 12V output, but that’s not true. In order to minimize dissipation the MCC is chosen in this application.
Resistor R determines the current as follows: This is a snapshot of page 8: All parameters are specified under certain conditions, and for the output voltage we mmc7812 see that the condition is that the input voltage is minimum They are like a variable series resistor between input and output, causing a voltage drop across the regulator.
Normally good construction techniques should be used to minimize ground loops and lead resistance drops since the regulator has no external sense lead.
The maximum dropout voltage Vd is 2. A is a linear regulator, and does not step up the input voltage if the input is below the output for that you need a DC-DC boost regulator. Home Questions Tags Users Unanswered. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
No External Components Required? Stresses exceeding Maximum Ratings may damage the device.
MC Datasheet PDF –
Representative Schematic Diagram http: Post as a guest Name. With adequate heatsinking they can deliver output currents in excess of 1. Current Regulator Figure 9. This is a snapshot of page How much higher depends on the type of regulator.
MC7812 Datasheet PDF
A control element will vary the resistance in practice a transistor so dataeheet the output voltage will remain constant regardless of input voltage and load. Values of less than 0. For example, a 1.
So the dataasheet delivers 20W, while the load only consumes 12W. Since the output is 12 volts, you add the two together to get a minimum input of Output Transistor Safe-Area Compensation? The circuit of Figure 10 can be modified to provide supply protection against short circuits by adding a short circuit sense resistor, RSC, and an additional PNP transistor.
Load and line regulation are specified at constant junction temperature. I’ve seen LDOs with a dropout voltage of 50 mV.
Linear regulators are different. The datasheet does say how much it needs, but you may have to look for it.
On the datasheet it doesn’t mention an input voltage. Long Term Stability – Output voltage stability under accelerated life test conditions with the maximum rated voltage listed in the devices’ electrical characteristics and maximum power dissipation. Therefore it’s best to keep the input voltage just above the minimum to prevent the regulator to become overheated. However, it is recommended that the regulator input be bypassed with a capacitor if the regulator is connected to the power supply filter with long wire lengths, datasehet if the output load capacitance is large.