Enviroline F Fiber filled for reinforcement. Enviroline® F is a polycyclamine cured epoxy novolac lining reinforced with both flake and fibre to. Enviroline FLT is a low temperature cure version of Enviroline F specifically designed to cure at temperatures down to -7°C. Enviroline® F is a solvent free, two component polycyclamine cured novolac epoxy lining system. Enviroline F • Resists continuous immersion in.
|Published (Last):||14 September 2009|
|PDF File Size:||13.2 Mb|
|ePub File Size:||12.20 Mb|
|Price:||Free* [*Free Regsitration Required]|
Extensive pitting, especially deep and convoluted pitting cannot be easily coated by such systems. Improvements to Enviroline Envirkline 58 and Enviroline R 59 include easier mixing, lower VOCs, no need for special thinners, and color changes.
Many lining failures can be directly attributed to primer applications that have filled in the blast profile. Areas of use include oil Enviroline 58 is epoxy polyamide rust inhibitive primer; Enviroline 59 is for A Handy Checklist for a Successful Lining.
It resists combination of water with high-temperature envirolinee or gas. Thomas Industry Update Stay up to date on industry news 367 trends, product announcements and the latest innovations. In establishing the cure of any lining system, a rub with a MEK wetted clean, white rag works well as an indicator of solvent resistance.
The company has installed more than 25 Enviroline units since October and has been a strong proponent of the technology for A Heavy-Duty system applied at This system can be used in ejviroline of more labor intensive and costly hand lay-up and chopped fiberglass systems see our site Reinforced Tank Linings.
An inspection blast conforming to SP-6 Commercial Blast is usually sufficient and also serves to help with an assessment dnviroline metal loss and pitting. A holding primer should be applied to the blasted steel within an 8 hour period to protect it from re-rusting.
If necessary, additional cleaning steps will be dnviroline to eliminate this condition. Be aware of any other pertinent factors, such as abrasion or temperature. People in the News. Consult Avilion to verify the suitability of any proposed coating.
Stay up to date on industry news and trends, product announcements and the latest innovations. It does not require preheating prior to application and is suited for tank and pipe owners as well as contractors. Adequate cleaning must be employed to avoid previous tank contents from seeping out of rivets, seams, butt straps, etc. A Handy Checklist for a Successful Lining The first step of a successful lining application is to ensure the proper coating is selected, one that will withstand the anticipated service.
Pompano Beach, FL Share: Company News Blount Rd. Web Hosting by Yahoo! This should provide information about the structural stability, shell plate movement, gaps in seam overlaps, missing rivets, etc.
Enivroline offers owners and applicators choice of application speed and curing results without affecting quality of chemically resistant barrier.
Ooooops!!! Account Suspended – Cuenta Suspendida
Though Jim never left the Enviroline Team completely – he recommended, estimated and applied Enviroline coatings and linings as a contractor for the last several years – Jim has returned to Enviroline sales to end the physical demands of his Enviroline 58HS enables users to hold surface preparation for up to 90 days while still meeting VOC requirements. Where possible, rivet seams should be sealed from the interior of the tank. Notes on Lining Tanks. Riveted tanks present a special set of sealing and lining difficulties.
A chemical resistant epoxy primer like Enviroline 58HS applied at 0. Enviroline ultra-high solids, thick-film epoxy coating exhibits chemical- and solvent-resistance in addition to abrasion- and impact-resistance. Since most linings are tested as soon as practical, much sooner than at full cure, and since significant under-specified DFT readings are allowable within reason and providing the specified average is met 70 volts per mil of coating has been found to be thorough enough for adequate testing, while not causing harm to a freshly applied coating.
Each epoxy is suited for use as lining for storage tanks, process tanks, pipelines, and concrete containment areas in petroleum, chemical processing, and Enviroline 58 is now available in tan for greater contrast from IECC topcoats, and Enviroline 59 is lighter color to increase hiding ability of Envirothane TM Urethane topcoat.
Explosives, Armaments, and Weaponry. For example, a two-coat thin film system typically mils would be a poor choice for severely pitted plates. Pipe may be backfilled as early as 5 to 7 minutes tack free. All tanks, prior to abrasive cleaning, should be tested for the presence of hidden contamination, especially envieoline.
Envirolone is applied by putty knife or trowel. Hardness gauges can be used as a more accurate and quantitative indication of cure, but, as it pinpricks the film, this must be considered a destructive test procedure. Offering thin-film application of up to 20 mils DFT, Enviroline UHS is suited for use as internal lining for storage tanks, process vessels, pipelines, and concrete containment structures requiring corrosion protection from refined petroleum products and chemicals.
Old tanks, upon coming out of service for refurbishment, present a wide variety of steel substrate conditions. It features high-solids, single-coat, fast cure technology. Product is available in 22 standard colors, including 5 safety colors.
Holiday testing should be performed using a maximum of volts per mil of applied, fully cured coating.
When sealing riveted exteriors, it is most often necessary to lower the content level in the tank to avoid problems with seep envieoline. In establishing the Dry Film Thickness for any lining system, be aware of the need to rely on a statistical average, as DFT varies often widely from place to place in a tank.
Some tanks may not be suitable for integrity restoration using these linings. Choice of a envirolinw system will often depend on the degree of corrosion found on the floor.
This step lessens the risk of re-contaminating the primed surfaces when proceeding with the final blast work.